LNP™ STAT-KON™ Compound CD000I

Chemical Family: Styrenics

LNP STAT-KON CD000I compound is based on Polystyrene (PS) resin containing conductive carbon powder. Added features of this grade include: Electrically Conductive, High Impact.

Product families

Applications

Industrial — Chemical & Industrial Manufacturing

Equipment & Parts

Electrical & Electronics — Devices & Assemblies

Industrial Automation

Electrical & Electronics — Parts & Components

Semiconductor Manufacturing

Product Families

Plastics — Basic Thermoplastics

Styrenics

Other characteristics

Brand: LNP™ STAT-KON™ Compound
Polymer Name: Polystyrene (unspecified)
Fillers Included: Carbon Black, Carbon Powder
Carbon Black
Carbon Powder
Additives Included: Heat Stabilizer, Impact Modifier
Heat Stabilizer
Impact Modifier
Processing Methods: Injection Molding
Note: ᵈ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding. Do NOT mix NORYL GTX* resin with other grades of NORYL* resins. Polystyrene and acrylic regrind are effective purging Materials. Use temperature range appropriate for particular purging resin. Regrind must also be dried. Maximum 25% regrind. Dry at recommended temperatures and times for optimum performance. Overdrying can cause loss of physical properties and/or create appearance defects. Do not exceed recommended basic drying time and temperature above or:\n4-8 hrs at 95°C (200°F), 10 hrs max\n6-12 hrs at 80°C (175°F), 16 hrs max\n8-16 hrs at 65°C (150°F), 24 hrs max\nAVOID air circulating tray ovens. Moisture levels in heated ambient air can exceed moisture level in the resin itself, causing moisture ABSORPTION not drying. Avoid melt temperature in excess of 300°C (575°F) and residence times over 6-8 minutes (may affect properties and/or appearance). Nozzle temperature controls assist in elimination of drool premature freeze-off. Shot sizes in excess of 50% barrel capacity can lead to difficulties in providing a consistent, homogenous plastic melt.; ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Electrical & Electronics
Industrial
Flame Rating: UL 94 HB
Technology: Plastics
Material Features: Electrically Conductive
Heat Stabilized
High Impact Performance
High Impact Resistance
Impact Modified
Country Availability: Canada
China (Mainland)
Mexico
USA
Certifications and Compliance: UL 94
Plastics and Elastomers End Uses: Electrical/Electronic Applications
Electronic Components
Industrial Applications
Semiconductor Applications
Plastics and Elastomers Functions: Resin
Plastics and Elastomers Processing Methods: Injection Molding

Technical data

Table 1 of 7

19 rows

Characteristic	Value	Unit	Method
Tensile Stress (Break) ¹¹	20	MPa	ASTM D638
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹	23	MPa	ASTM D638
Tensile Strain (Break) ¹¹	6.6	%	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	16	MPa	ASTM D638
Tensile Modulus (at 50 mm/min) ¹¹	2170	MPa	ASTM D638
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹	1.2	%	ASTM D638
Flexural Stress ¹¹	40	MPa	ISO 178
Flexural Stress ¹¹	41	MPa	ASTM D790
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	9.7	%	ASTM D638
Flexural Modulus ¹¹	2690	MPa	ASTM D790
Tensile Modulus (at 5 mm/min) ¹¹	2280	MPa	ASTM D638
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹	42	MPa	ASTM D790

Table 2 of 7

6 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.08	g/cm³	ASTM D792
Specific Gravity ¹¹	1.08	—	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.1	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.3 - 0.7	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.4 - 0.7	%	ASTM D955
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.13	%	ISO 62

Table 3 of 7

6 rows

Characteristic	Value	Unit	Method
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	75	°C	ASTM D648
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	87	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.000098	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.000107	1/°C	ASTM E831
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80104, sp=64mm) ¹¹	87	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	78	°C	ISO 75/Af

Table 4 of 7

1 row

Characteristic	Value	Unit	Method
Surface Resistivity ᵈ ¹¹	100 - 1000000	Ω	ASTM D257

Table 5 of 7

8 rows

Characteristic	Value	Unit	Method
Izod Impact (Unnotched, at 23°C) ¹¹	384	J/m	ASTM D4812
Izod Impact (Unnotched, at 23°C) ¹¹	744	J/m	ASTM D4812
Izod Impact (Notched, at 23°C) ¹¹	48	J/m	ASTM D256
Izod Impact (Notched, at 23°C) ¹¹	82	J/m	ASTM D256
Multi-Axial Impact ¹¹	15	J	ISO 6603
Instrumented Dart Impact Total Energy (at 23°C) ¹¹	18	J	ASTM D3763
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	31	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80104, at 23°C) ¹¹	5	kJ/m²	ISO 180/1A

Table 6 of 7

9 rows

Characteristic	Value	Unit
Drying Temperature ⁷	80	°C
Drying Time ⁷	4	Hrs
Melt Temperature ⁷	250	°C
Front - Zone 3 Temperature ⁷	265 - 275	°C
Middle - Zone 2 Temperature ⁷	245 - 255	°C
Rear - Zone 1 Temperature ⁷	220 - 230	°C
Mold Temperature ⁷	40 - 65	°C
Back Pressure ⁷	0.2 - 0.3	MPa
Screw Speed ⁷	30 - 60	rpm

Table 7 of 7