LNP™ LUBRILOY™ Compound R2000AXP

Chemical Family: Polyamides

LNP LUBRILOY R2000AXP compound is based on Nylon 6/6 resin containing proprietary lubricant. Added features of this grade include: Wear Resistant.

Product families

Plastics — Engineering & Specialty Polymers

Polyamides

Other characteristics

Brand: LNP™ LUBRILOY™ Compound
Polymer Name: Polyamide 66 (PA 66)
Additives Included: Lubricant (Unspecified), Proprietary
Lubricant (Unspecified)
Proprietary
Processing Methods: Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Building & Construction
Consumer Goods
Electrical & Electronics
Personal Care
Printing & Packaging
Technology: Plastics
Product Features: Good wear
Low COF
Material Features: Lubricated
Unreinforced
Wear Resistant
Compounds Feature: Improved impact over PTFE filled materials
Lower mold deposits
Excellent surface finish & colorability
Lower S.G. vs. PTFE filled materials
Non-halogenated lubrication
Plastics and Elastomers End Uses: Appliances
Building Materials
Cell Phones
Commercial Appliance
Computer Components
Consumer Applications
Containers
Damping Bands
Compounds Applications: PA 6/6 based LUBRILOY alloys are typically used in automotive and industrial applications for gears, sliders, bearings and bushings. They feature good wear, low friction, low moisture absorption and good vibration damping characteristics.
Plastics and Elastomers Functions: Resin

Technical data

Table 1 of 5

14 rows

Characteristic	Value	Unit	Method
Tensile Stress (Yield) ¹¹	69	MPa	ISO 527
Tensile Stress (Yield) ¹¹	82	MPa	ASTM D638
Tensile Stress (Break) ¹¹	67	MPa	ASTM D638
Tensile Stress (Break) ¹¹	57	MPa	ISO 527
Tensile Strain (Yield) ¹¹	5.2	%	ASTM D638
Tensile Strain (Yield) ¹¹	17.2	%	ISO 527
Tensile Strain (Break) ¹¹	24.4	%	ASTM D638
Tensile Strain (Break) ¹¹	3.14E+01	%	ISO 527
Tensile Modulus (at 50 mm/min) ¹¹	3040	MPa	ASTM D638
Flexural Stress ¹¹	90	MPa	ISO 178
Flexural Stress ¹¹	105	MPa	ASTM D790
Flexural Modulus ¹¹	2790	MPa	ASTM D790

Table 2 of 5

11 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.12	g/cm³	ISO 1183
Density ¹¹	1.12	g/cm³	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.88	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	2.3 - 2.5	%	ASTM D955
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	2.31 - 2.52	%	ISO 294
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	2.3 - 2.5	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	2.31 - 2.52	%	ISO 294
Wear Factor Washer ¹¹	10	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.3	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.16	—	ASTM D3702 Modified: Manual
Moisture Absorption (at 23°C, 50% RH) ¹¹	1.18	%	ISO 62

Table 3 of 5

6 rows

Characteristic	Value	Unit	Method
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	58	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000986	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000986	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000912	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000913	1/°C	ISO 11359-2
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	58	°C	ISO 75/Af

Table 4 of 5