LNP™ LUBRICOMP™ Compound 9X06483

Chemical Family: Polyamides

LNP LUBRICOMP 9X06483 compound is based on a Nylon 4/6 resin containing PTFE. Added features of this grade include: Wear Resistant, Heat Stabilized.

Product families

Applications

Consumer Goods — Appliances & Electronics

Automotive & Transportation — Automotive

Aftermarket Parts & Components
Powertrain & UTH

Industrial — Chemical & Industrial Manufacturing

Equipment & Parts

Electrical & Electronics — Devices & Assemblies

Consumer Electronics
Displays

Electrical & Electronics — Parts & Components

Semiconductor Manufacturing

Product Families

Plastics — Engineering & Specialty Polymers

Polyamides

Other characteristics

Brand: LNP™ LUBRICOMP™ Compound
Polymer Name: Polyamide 46 (PA 46)
Fillers Included: PTFE
Flexural Modulus: 2800.0 - 2800.0 MPa
Additives Included: Heat Stabilizer, Lubricant (PTFE)
Heat Stabilizer
Lubricant (PTFE)
Processing Methods: Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Automotive & Transportation
Consumer Goods
Electrical & Electronics
Industrial
Technology: Plastics
Material Features: Heat Stabilized
Lubricated
Unreinforced
Wear Resistant
Plastics and Elastomers End Uses: Appliances
Automotive Applications
Automotive Under The Hood
Cell Phones
Commercial Appliance
Computer Components
Consumer Applications
Displays
Plastics and Elastomers Functions: Resin
Plastics and Elastomers Processing Methods: Injection Molding

Technical data

Table 1 of 5

13 rows

Characteristic	Value	Unit	Method
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹	80	MPa	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	74	MPa	ASTM D638
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹	5.8	%	ASTM D638
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	5.9	%	ASTM D638
Tensile Modulus (at 5 mm/min) ¹¹	3130	MPa	ASTM D638
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	2960	MPa	ASTM D790
Tensile Stress (Yield, 5 mm/min) ¹¹	78	MPa	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	76	MPa	ISO 527
Tensile Strain (Yield, 5 mm/min) ¹¹	6.5	%	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	6.6	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	3000	MPa	ISO 527
Flexural Strength (at 2 mm/min) ¹¹	101	MPa	ISO 178

Table 2 of 5

10 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.28	g/cm³	ISO 1183
Density ¹¹	1.29	g/cm³	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	1.8	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	1 - 3	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	2 - 4	%	ASTM D955
Wear Factor Washer ¹¹	11	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Wear Factor Ring ¹¹	-1	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.32	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.32	—	ASTM D3702 Modified: Manual
Moisture Absorption (at 23°C, 50% RH) ¹¹	2.7	%	ISO 62

Table 3 of 5

5 rows

Characteristic	Value	Unit	Method
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	283	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	151	°C	ASTM D648
Coefficient of Thermal Expansion (at -30°C to 30°C, xflow) ¹¹	0.000093	1/°C	ASTM D696
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80104, sp=64mm) ¹¹	276	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	92	°C	ISO 75/Af

Table 4 of 5