To catalogue
LNP™ LUBRICOMP™ Compound GFL36L
- Chemical Family
- Polysulfones
SABIC's Specialties Business LNP LUBRICOMP GFL36L compound is based on Polysulfone (PSU) resin containing 30% glass fiber, 15% PTFE. Added features of this grade include: Low Extractable, Wear Resistant.
Product families
Applications
Applications
- Consumer Goods — Appliances & Electronics
Building & Construction — Building Materials
- Pipes & Plumbing
Industrial — Chemical & Industrial Manufacturing
- Equipment & Parts
Electrical & Electronics — Devices & Assemblies
- Consumer Electronics
Printing & Packaging — Packaging
- Food & Beverage Packaging
- Industrial & Transport Packaging
- Non-Food Consumer Packaging
Electrical & Electronics — Parts & Components
- Housings & Enclosures
Product Families
Plastics — Engineering & Specialty Polymers
- High Performance Thermoplastics
Other characteristics
- Brand
- LNP™ LUBRICOMP™ Compound
- Polymer Name
- Polysulfone (PSU)
- Fillers Included
- Glass Fiber, PTFE
- Glass Fiber
- PTFE
- Flexural Modulus
- 8960.0 - 8960.0 MPa
- Additives Included
- Lubricant (PTFE)
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Industrial
- Printing & Packaging
- Technology
- Plastics
- Labeling Claims
- Food Contact Acceptable
- Material Features
- Food Contact Acceptable
- Friction Resistant
- High Stiffness
- High Temperature Resistance
- Low Extractables
- Low Leachable
- Very Good Heat Resistance
- Wear Resistant
- Plastics and Elastomers End Uses
- Appliances
- Building Materials
- Consumer Applications
- Conveyors
- Covers
- Enclosure
- Food Packaging
- Home Appliances
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 5
14 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield) ¹¹ | 88 | MPa | ASTM D638 |
| Tensile Stress (Yield) ¹¹ | 87 | MPa | ISO 527 |
| Tensile Stress (Break) ¹¹ | 88 | MPa | ASTM D638 |
| Tensile Stress (Break) ¹¹ | 87 | MPa | ISO 527 |
| Tensile Strain (Yield) ¹¹ | 1.3 | % | ISO 527 |
| Tensile Strain (Yield) ¹¹ | 1.3 | % | ASTM D638 |
| Tensile Strain (Break) ¹¹ | 1.3 | % | ASTM D638 |
| Tensile Strain (Break) ¹¹ | 1.2 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 9330 | MPa | ISO 527 |
| Flexural Stress ¹¹ | 121 | MPa | ISO 178 |
| Flexural Stress ¹¹ | 110 | MPa | ASTM D790 |
| Flexural Modulus ¹¹ | 8960 | MPa | ASTM D790 |
Table 2 of 5
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹¹ | 1.62 | g/cm³ | ASTM D792 |
| Density ¹¹ | 1.62 | g/cm³ | ISO 1183 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.2 - 0.4 | % | ASTM D955 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.26 | % | ISO 294 |
| Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ | 0.4 - 0.6 | % | ASTM D955 |
| Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ | 0.51 | % | ISO 294 |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.1 | % | ASTM D570 |
| Wear Factor Washer ¹¹ | 44 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Dynamic COF ¹¹ | 0.42 | — | ASTM D3702 Modified: Manual |
| Static COF ¹¹ | 0.62 | — | ASTM D3702 Modified: Manual |
Table 3 of 5
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 186 | °C | ISO 75/Bf |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 181 | °C | ISO 75/Af |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.000024 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.0000252 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.00003 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.0000306 | 1/°C | ASTM E831 |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 185 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 180 | °C | ASTM D648 |
Table 4 of 5
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 8 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 23 | kJ/m² | ISO 180/1U |
| Multi-Axial Impact ¹¹ | 3 | J | ISO 6603 |
| Izod Impact (Notched, at 23°C) ¹¹ | 74 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 341 | J/m | ASTM D4812 |
| Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ | 14 | J | ASTM D3763 |
Table 5 of 5
10 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 120 - 150 | °C |
| Drying Time ⁷ | 4 | Hrs |
| Maximum Moisture Content ⁷ | 0.05 | % |
| Melt Temperature ⁷ | 360 - 370 | °C |
| Front - Zone 3 Temperature ⁷ | 350 - 360 | °C |
| Middle - Zone 2 Temperature ⁷ | 340 - 350 | °C |
| Rear - Zone 1 Temperature ⁷ | 325 - 340 | °C |
| Mold Temperature ⁷ | 150 | °C |
| Back Pressure ⁷ | 0.2 - 0.3 | MPa |
| Screw Speed ⁷ | 30 - 60 | rpm |
