LNP™ VERTON™ Compound RVL29U
- Chemical Family
- Polyamides
LNP™ VERTON™ Compound RVL29U utilizes Polyamide 66 (nylon 66) resin combined with 45% long glass fiber and 10% PTFE to provide a robust solution featuring UV stabilization, wear resistance, and structural integrity. This compound is designed for applications requiring durability and reliability in outdoor environments, offering enhanced resistance to weathering and prolonged exposure to sunlight. The addition of PTFE enhances the material's wear resistance, reducing friction and ensuring prolonged performance in demanding conditions. LNP™ VERTON™ Compound RVL29U is suitable for a wide range of applications including automotive components, electrical enclosures, and industrial machinery where high mechanical strength and longevity are crucial. Its composition supports efficient processing and consistent quality in injection molding processes, ensuring precision and reliability in component manufacturing.
Product families
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Sports & Recreation
- Exterior & Body
- Structural Components
- Industrial Automation
Product Families
- Polyamides
Other characteristics
- Brand
- LNP™ VERTON™ Compound
- Polymer Name
- Polyamide 66 (PA 66)
- Fillers Included
- Glass Fiber, PTFE
- Glass Fiber
- PTFE
- Processing Methods
- Injection Molding
- Note
(1) The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design. (2) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article. (3) Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- Markets
- Automotive & Transportation
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Technology
- Plastics
- Material Features
- Easy To Mold
- Good Processability
- Good UV Stability
- Good Weather Stability
- High Stiffness
- High Strength
- UV Stabilized
- Wear Resistant
- Plastics and Elastomers End Uses
- Automotive Exterior Parts
- Building Materials
- Commercial Appliance
- Home Appliances
- Sporting Goods
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 5
13 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Modulus (at 1 mm/min) ¹ | 16000.0 | MPa | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹ | 230.0 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹ | 3.0 | % | ISO 527 |
| Flexural Modulus (at 2 mm/min) ¹ | 13000.0 | MPa | ISO 178 |
| Flexural Strength (2 mm/min) ¹ | 330.0 | MPa | ISO 178 |
| Hardness (Rockwell R) ¹ | 115.0 | — | ISO 2039-2 |
| Hardness (Rockwell M) ¹ | 112.0 | — | ISO 2039-2 |
| Hardness (Rockwell L) ¹ | 96.0 | — | ISO 2039-2 |
| Tensile Modulus (at 5 mm/min) ¹ | 16000.0 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹ | 220.0 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹ | 2.8 | % | ASTM D638 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹ | 12800.0 | MPa | ASTM D790 |
Table 2 of 5
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹ | 1.64 | g/cm³ | ISO 1183 |
| Moisture Absorption (23°C/50% RH/24hrs) ¹ | 0.4 - 0.6 | % | ISO 62-4 |
| Water Absorption (23°C/saturated) ¹ | 3.2 - 3.8 | % | ISO 62-1 |
| Specific Gravity ¹ | 1.66 | — | ASTM D792 |
| Wear Factor Washer ¹ | 25.0 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Instr. |
| Dynamic Coefficient of Friction ¹ | 0.42 | — | ASTM D3702 Modified: Instr. |
| Static COF ¹ | 0.48 | — | ASTM D3702 Modified: Instr. |
| Mold Shrinkage (flow) ² | 0.2 - 0.4 | % | SABIC method |
| Mold Shrinkage (xflow) ² | 0.7 - 0.9 | % | SABIC method |
Table 3 of 5
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature/Af (1.8 MPa Flatw 80*10*4 sp=64mm) ¹ | 255.0 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (0.45 MPa Flatw 80*10*4 sp=64mm) ¹ | 260.0 | °C | ISO 75/Bf |
| Vicat Softening Temperature (at Rate B/50) ¹ | 247.0 | °C | ISO 306 |
| Vicat Softening Temperature (at Rate B/120) ¹ | 253.0 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹ | 1.4e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹ | 6.0e-05 | 1/°C | ISO 11359-2 |
Table 4 of 5
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched 80*10*4 +23°C) ¹ | 27.0 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched 80*10*4 -40°C) ¹ | 27.0 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched 80*10*4 +23°C) ¹ | 81.0 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched 80*10*4 -40°C) ¹ | 76.0 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹ | 31.0 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹ | 80.0 | kJ/m² | ISO 179/1eU |
| Multi-Axial Instrumented Impact Total Energy (at 23°C) ¹ | 12.0 | J | ISO 6603-2 |
| Izod Impact (Notched, 23°C) ¹ | 170.0 | J/m | ASTM D256 |
| Izod Impact (Unnotched, 23°C) ¹ | 1090.0 | J/m | ASTM D4812 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹ | 10.0 | J | ASTM D3763 |
Table 5 of 5
13 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ³ | 80.0 | °C |
| Drying Time ³ | 4.0 | Hrs |
| Drying Time (Cumulative) ³ | 48.0 | Hrs |
| Maximum Moisture Content ³ | 0.15 - 0.25 | % |
| Hopper Temperature ³ | 40.0 | °C |
| Melt Temperature ³ | 290 - 305 | °C |
| Rear - Zone 1 Temperature ³ | 280 - 295 | °C |
| Middle - Zone 2 Temperature ³ | 290 - 300 | °C |
| Front - Zone 3 Temperature ³ | 290 - 300 | °C |
| Nozzle Temperature ³ | 290 - 305 | °C |
| Mold Temperature ³ | 95 - 110 | °C |
| Back Pressure ³ | 0.2 - 0.3 | MPa |
