LNP™ VERTON™ Compound MV00AS
- Chemical Family
- PolyolefinsPolypropylenes (PP)
LNP™ VERTON™ Compound MV00AS combines polypropylene (PP) resin with a high 50% long glass fiber content, offering exceptional structural strength and stiffness. Engineered with chemical coupling for enhanced performance, this compound is heat stabilized to maintain integrity under varying temperatures. It is tailored for rigorous applications in automotive exteriors, water management systems, sports and leisure equipment, as well as home and commercial appliances. MV00AS excels in injection molding processes, ensuring reliable performance in demanding industrial environments where high stiffness and dimensional stability are critical.
Product families
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Sports & Recreation
- Exterior & Body
- Equipment & Parts
- Consumer Electronics
Product Families
- Polyolefins
Other characteristics
- Brand
- LNP™ VERTON™ Compound
- Polymer Name
- Polypropylene (unspecified)
- Fillers Included
- Glass Fiber, Long Glass Fiber
- Glass Fiber
- Long Glass Fiber
- Processing Methods
- Injection Molding
- Note
¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design. ² Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article. ³ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- Markets
- Automotive & Transportation
- Consumer Goods
- Electrical & Electronics
- Industrial
- Technology
- Plastics
- Labeling Claims
- No Added PFAS
- Material Features
- Chemically Coupled
- Heat Stabilized
- High Stiffness
- High Strength
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Automotive Applications
- Commercial Appliance
- Construction Applications
- Home Appliances
- Water Management
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Modulus (at 5 mm/min) ¹ | 10440.0 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹ | 131.0 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹ | 1.8 | % | ASTM D638 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹ | 9350.0 | MPa | ASTM D790 |
| Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹ | 190.0 | MPa | ASTM D790 |
| Tensile Stress (Break, 5 mm/min) ¹ | 140.0 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹ | 1.5 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹ | 14000.0 | MPa | ISO 527 |
| Flexural Stress (Break, 2 mm/min) ¹ | 209.0 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹ | 11700.0 | MPa | ISO 178 |
Table 2 of 6
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹ | 1.33 | g/cm³ | ASTM D792 |
| Density ¹ | 1.33 | g/cm³ | ISO 1183 |
| Wear Factor Washer ¹ | 73.0 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Dynamic Coefficient of Friction ¹ | 0.34 | — | ASTM D3702 Modified: Manual |
| Static COF ¹ | 0.52 | — | ASTM D3702 Modified: Manual |
Table 3 of 6
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (1.82 MPa, 3.2mm, unannealed) ¹ | 157.0 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹ | 3.4e-05 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹ | 3.4e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹ | 4.6e-05 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹ | 4.6e-05 | 1/°C | ISO 11359-2 |
| Heat Deflection Temperature/Bf (0.45 MPa Flatw 80*10*4 sp=64mm) ¹ | 164.0 | °C | ISO 75/Bf |
| Heat Deflection Temperature/Af (1.8 MPa Flatw 80*10*4 sp=64mm) ¹ | 159.0 | °C | ISO 75/Af |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹ | 3.4e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹ | 4.6e-05 | 1/°C | ISO 11359-2 |
Table 4 of 6
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, 23°C) ¹ | 208.0 | J/m | ASTM D256 |
| Instrumented Dart Impact Energy (at peak, 23°C) ¹ | 13.0 | J | ASTM D3763 |
| Izod Impact (Unnotched 80*10*4 +23°C) ¹ | 55.0 | kJ/m² | ISO 180/1U |
| Izod Impact (Notched 80*10*4 +23°C) ¹ | 27.0 | kJ/m² | ISO 180/1A |
| Multiaxial Impact ¹ | 13.0 | J | ISO 6603 |
Table 5 of 6
9 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ³ | 80.0 | °C |
| Drying Time ³ | 4.0 | Hrs |
| Melt Temperature ³ | 220 - 250 | °C |
| Front - Zone 3 Temperature ³ | 250 - 260 | °C |
| Middle - Zone 2 Temperature ³ | 245 - 255 | °C |
| Rear - Zone 1 Temperature ³ | 230 - 245 | °C |
| Mold Temperature ³ | 40 - 65 | °C |
| Back Pressure ³ | 0.2 - 0.3 | MPa |
| Screw Speed ³ | 30 - 60 | rpm |
Table 6 of 6
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized 94HB Flame Class Rating ² | 1.5 | mm | UL 94 |
