LNP™ VERTON™ Compound RVN1AESP
- Chemical Family
- Polyamides
LNP™ VERTON™ Compound RVN1AESP features Polyamide 66 (nylon 66) resin with 50% long glass fiber and a proprietary lubricant, designed for applications requiring easy molding, wear resistance, and structural integrity. This compound is engineered to provide excellent processability in injection molding, allowing for the efficient production of complex shapes and components. Its enhanced wear resistance ensures durability in demanding environments, making it suitable for industrial machinery, automotive parts, and other applications where mechanical performance is critical. This product offers reliable performance and longevity, supported by its high stiffness and strength characteristics, contributing to the overall reliability and longevity of the finished products.
Product families
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Sports & Recreation
- Exterior & Body
- Structural Components
- Industrial Automation
Product Families
- Polyamides
Other characteristics
- Brand
- LNP™ VERTON™ Compound
- Polymer Name
- Polyamide 66 (PA 66)
- Fillers Included
- Glass Fiber, Proprietary
- Glass Fiber
- Proprietary
- Processing Methods
- Injection Molding
- Note
(1) The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design. (2) Test speed = 6.7m/s (3) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article. (4) Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- Markets
- Automotive & Transportation
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Technology
- Plastics
- Labeling Claims
- No Added PFAS
- Material Features
- Easy To Mold
- High Stiffness
- High Strength
- Wear Resistant
- Plastics and Elastomers End Uses
- Automotive Exterior Parts
- Building Materials
- Commercial Appliance
- Home Appliances
- Sporting Goods
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 5
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Break, Type I, 5 mm/min) ¹ | 250.0 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹ | 2.1 | % | ASTM D638 |
| Tensile Modulus (at 5 mm/min) ¹ | 16700.0 | MPa | ASTM D638 |
| Flexural Strength (1.3 mm/min, 50 mm span) ¹ | 320.0 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹ | 11800.0 | MPa | ASTM D790 |
| Tensile Stress (Break, 5 mm/min) ¹ | 235.0 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹ | 2.4 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹ | 17000.0 | MPa | ISO 527 |
| Flexural Strength (2 mm/min) ¹ | 330.0 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹ | 11300.0 | MPa | ISO 178 |
Table 2 of 5
11 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Moisture Absorption (23°C/50% RH/24 hrs) ¹ | 0.1 | % | ASTM D570 |
| Water Absorption (23°C/24hrs) ¹ | 0.8 - 0.9 | % | ASTM D570 |
| Specific Gravity ¹ | 1.6 | — | ASTM D792 |
| Density ¹ | 1.6 | g/cm³ | ISO 1183 |
| Moisture Absorption (23°C / 50% RH) ¹ | 0.3 | % | ISO 62 |
| Water Absorption (23°C/saturated) ¹ | 4.4 | % | ISO 62-1 |
| Mold Shrinkage (flow, 24 hrs) ³ | 0.2 - 0.3 | % | ISO 294 |
| Mold Shrinkage (xflow, 24 hrs) ³ | 0.7 - 0.8 | % | ISO 294 |
| Wear Factor Washer ¹ | 33.0 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Instr. |
| Dynamic Coefficient of Friction ¹ | 0.58 | — | ASTM D3702 Modified: Instr. |
| Static COF ¹ | 0.71 | — | ASTM D3702 Modified: Instr. |
Table 3 of 5
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Vicat Softening Temperature (at Rate B/50) ¹ | 240.0 | °C | ISO 306 |
| Vicat Softening Temperature (at Rate B/120) ¹ | 235.0 | °C | ISO 306 |
| Heat Deflection Temperature/Bf (0.45 MPa Flatw 80*10*4 sp=64mm) ¹ | 250.0 | °C | ISO 75/Bf |
| Heat Deflection Temperature/Af (1.8 MPa Flatw 80*10*4 sp=64mm) ¹ | 245.0 | °C | ISO 75/Af |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹ | 1.4e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹ | 6.7e-05 | 1/°C | ISO 11359-2 |
Table 4 of 5
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Unnotched, 23°C) ¹ | 1160.0 | J/m | ASTM D4812 |
| Izod Impact (Notched, 23°C) ¹ | 270.0 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹ | 12.0 | J | ASTM D3763 |
| Izod Impact (Notched 80*10*4 +23°C) ¹ | 35.0 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched 80*10*4 -40°C) ¹ | 40.0 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched 80*10*4 +23°C) ¹ | 90.0 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹ | 35.0 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹ | 95.0 | kJ/m² | ISO 179/1eU |
| Multiaxial Impact ² | 13.0 | J | ISO 6603 |
Table 5 of 5
13 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁴ | 80.0 | °C |
| Drying Time ⁴ | 4.0 | Hrs |
| Drying Time (Cumulative) ⁴ | 48.0 | Hrs |
| Maximum Moisture Content ⁴ | 0.15 - 0.25 | % |
| Melt Temperature ⁴ | 290 - 305 | °C |
| Nozzle Temperature ⁴ | 290 - 305 | °C |
| Front - Zone 3 Temperature ⁴ | 290 - 300 | °C |
| Middle - Zone 2 Temperature ⁴ | 290 - 300 | °C |
| Rear - Zone 1 Temperature ⁴ | 280 - 295 | °C |
| Hopper Temperature ⁴ | 40.0 | °C |
| Mold Temperature ⁴ | 95 - 110 | °C |
| Back Pressure ⁴ | 0.2 - 0.3 | MPa |
