CYCOLOY™ FR Resin CX7510
SABIC's Specialties Business CYCOLOY CX7510 Polycarbonate/Acrylonitrile Butadiene Styrene (PC/ABS) blend is an injection moldable, high flow, high heat resistant, non chlorinated/brominated flame retardant grade. It has a UL94 V0@1.5mm and 5VB@1.5mm flame rating. This grade has improved chemical resistance compared to standard PC/ABS blends and is a good candidate for thin wall applications.
Product families
Applications
- Electrical & Electronic Systems
- Displays
- Batteries
Product Families
- Blends & Alloys
Other characteristics
- Brand
- CYCOLOY™ FR Resin
- Density
- 1180.0 - 1180.0 kg/m³
- Polymer Name
- PC/ABS Alloy
- Flexural Modulus
- 2620.0 - 2620.0 MPa
- Processing Methods
- Injection Molding
- Note
ʰ Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Electrical & Electronics
- Flame Rating
- UL 94 5VB
- UL 94 V0
- Technology
- Plastics
- Labeling Claims
- Bromine-free
- Chlorine-free
- Additives Included
- Flame Retardant
- Heat Stabilizer
- Material Features
- Flame Retardant
- Heat Stabilized
- High Flow
- High Flowability
- High Impact Resistance
- Non-brominated
- Non-chlorinated
- Unreinforced
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Displays
- EV Battery Modules
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
14 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 65 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 49 | MPa | ASTM D638 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 4 | % | ASTM D638 |
| Tensile Strain (Break, Type I, 50 mm/min) ¹¹ | 36 | % | ASTM D638 |
| Tensile Modulus (at 50 mm/min) ¹¹ | 2580 | MPa | ASTM D638 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ | 97 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 2330 | MPa | ASTM D790 |
| Tensile Stress (Yield, 50 mm/min) ¹¹ | 64 | MPa | ISO 527 |
| Tensile Stress (Break, 50 mm/min) ¹¹ | 48 | MPa | ISO 527 |
| Tensile Strain (Yield, 50 mm/min) ¹¹ | 4.5 | % | ISO 527 |
| Tensile Strain (Break, 50 mm/min) ¹¹ | 36 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 2540 | MPa | ISO 527 |
Table 2 of 6
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity ¹¹ | 1.18 | — | ASTM D792 |
| Mold Shrinkage (flow, 3.2 mm) ʰ ¹¹ | 0.56 - 0.63 | % | SABIC method |
| Melt Flow Rate (at 260°C, 2.16 kgf) ¹¹ | 16 | g/10 min | ASTM D1238 |
| Melt Flow Rate (at 260°C, 5.0 kgf) ¹¹ | 45 | g/10 min | ASTM D1238 |
| Density ¹¹ | 1.18 | g/cm³ | ISO 1183 |
| Water Absorption (at 23°C, saturated) ¹¹ | 0.11 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.05 | % | ISO 62 |
| Melt Volume Rate (at 260°C, 5.0 kg) ¹¹ | 41 | cm³/10 min | ISO 1133 |
Table 3 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Vicat Softening Temperature (Rate B/50) ¹¹ | 113 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 115 | °C | ISO 306 |
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ | 106 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.000069 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.000072 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.000075 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.000072 | 1/°C | ASTM E831 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 118 | °C | ISO 306 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 95 | °C | ISO 75/Af |
| Relative Temperature Index (Electrical) ᵖ ¹¹ | 60 | °C | UL 746B |
| Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 60 | °C | UL 746B |
| Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 60 | °C | UL 746B |
Table 4 of 6
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹¹ | 640 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹¹ | 137 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 65 | J | ASTM D3763 |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 36 | kJ/m² | ISO 179/1eA |
Table 5 of 6
14 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 90 - 100 | °C |
| Drying Time ⁷ | 2 - 4 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.04 | % |
| Melt Temperature ⁷ | 270 - 300 | °C |
| Nozzle Temperature ⁷ | 265 - 300 | °C |
| Front - Zone 3 Temperature ⁷ | 265 - 300 | °C |
| Middle - Zone 2 Temperature ⁷ | 260 - 300 | °C |
| Rear - Zone 1 Temperature ⁷ | 260 - 300 | °C |
| Mold Temperature ⁷ | 60 - 90 | °C |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa |
| Screw Speed ⁷ | 40 - 70 | rpm |
Table 6 of 6
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized (94-5VB Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
| UL Recognized (94V-0 Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
