To catalogue
LEXAN™ VISUALFX™ Resin FXC630SK
PC+ABS, ECO-conforming flame retardant with diamond sparkle appearance. Color package may affect performance.
Product families
Applications
Applications
- Consumer Goods — Appliances & Electronics
Electrical & Electronics — Devices & Assemblies
- Consumer Electronics
- Displays
Printing & Packaging — Packaging
- Food & Beverage Packaging
Electrical & Electronics — Parts & Components
- Connectors
- Housings & Enclosures
- Switches & Relays
Product Families
Plastics — Engineering & Specialty Polymers
- Blends & Alloys
Other characteristics
- Brand
- LEXAN™ VISUALFX™ Resin
- Density
- 1190.0 - 1190.0 kg/m³
- Polymer Name
- PC/ABS Alloy
- Flexural Modulus
- 2600.0 - 2600.0 MPa
- Processing Methods
- Injection Molding
- Note
ʰ Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Consumer Goods
- Electrical & Electronics
- Printing & Packaging
- Flame Rating
- UL 94 5VB
- UL 94 V0
- UL 94 V1
- UL 94 V2
- Technology
- Plastics
- Labeling Claims
- Confirms to ECO-Label
- Additives Included
- Flame Retardant
- Material Features
- Flame Retardant
- Good Aesthetics
- Good Surface Appearance
- Non-brominated
- Non-chlorinated
- Unreinforced
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Appliances
- Cash Dispenser (ATM)
- Cell Phones
- Commercial Appliance
- Commercial Cookware
- Computer Components
- Consumer Applications
- Covers
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 7
22 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Taber Abrasion (CS-17, 1 kg) ¹¹ | 82 | mg/1000cy | SABIC method |
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 59 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 46 | MPa | ASTM D638 |
| Tensile Stress (Yield, 5 mm/min) ¹¹ | 50 | MPa | ISO 527 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 4 | % | ASTM D638 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 40 | MPa | ISO 527 |
| Tensile Strain (Break, Type I, 50 mm/min) ¹¹ | 20 | % | ASTM D638 |
| Tensile Strain (Yield, 5 mm/min) ¹¹ | 4 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 2800 | MPa | ISO 527 |
| Tensile Modulus (at 50 mm/min) ¹¹ | 3100 | MPa | ASTM D638 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ | 94 | MPa | ASTM D790 |
| Flexural Stress (Yield, at 2 mm/min) ¹¹ | 98 | MPa | ISO 178 |
Table 2 of 7
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Mold Shrinkage (on Tensile Bar, flow) ʰ ¹¹ | 0.4 - 0.6 | % | SABIC method |
| Density ¹¹ | 1.2 | g/cm³ | ISO 1183 |
| Water Absorption (at 23°C, saturated) ¹¹ | 0.6 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.2 | % | ISO 62 |
| Specific Gravity ¹¹ | 1.19 | — | ASTM D792 |
| Melt Volume Rate (at 260°C, 2.16 kg) ¹¹ | 14 | cm³/10 min | ISO 1133 |
| Melt Volume Rate (at 260°C, 2.16 kg) ¹¹ | 13 | cm³/10 min | ISO 1133 |
| Mold Shrinkage (flow, 3.2 mm) ʰ ¹¹ | 0.3 - 0.5 | % | SABIC method |
| Melt Flow Rate (at 260°C, 2.16 kgf) ¹¹ | 13.5 | g/10 min | ASTM D1238 |
| Density (Molded) ¹¹ | 1.2 | g/cm³ | ISO 1183 |
Table 3 of 7
16 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Thermal Conductivity ¹¹ | 0.2 | W/m-°C | ISO 8302 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.000075 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.000072 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.000075 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.000072 | 1/°C | ASTM E831 |
| Ball Pressure Test (at 73°C to 77°C) ¹¹ | Pass | — | IEC 60695-10-2 |
| Ball Pressure Test (approximate maximum) ¹¹ | 85 | °C | IEC 60695-10-2 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 98 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 94 | °C | ISO 306 |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 90 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 82 | °C | ASTM D648 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 97 | °C | ISO 306 |
Table 4 of 7
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Volume Resistivity ¹¹ | min. 1.E+15 | Ω.cm | IEC 60093 |
| Surface Resistivity (ROA) ¹¹ | min. 1.E+15 | Ω | IEC 60093 |
| Dielectric Strength (in oil, at 0.8mm) ¹¹ | 35 | kV/mm | IEC 60243-1 |
| Dielectric Strength (in oil, at 1.6mm) ¹¹ | 25 | kV/mm | IEC 60243-1 |
| Dielectric Strength (in oil, at 3.2mm) ¹¹ | 17 | kV/mm | IEC 60243-1 |
| Relative Permittivity (1 MHz) ¹¹ | 2.7 | — | IEC 60250 |
| Dissipation Factor (at 50/60 Hz) ¹¹ | 0.004 | — | IEC 60250 |
| Dissipation Factor (at at 1 MHz) ¹¹ | 0.008 | — | IEC 60250 |
| Relative Permittivity (50/60 Hz) ¹¹ | 2.8 | — | IEC 60250 |
Table 5 of 7
7 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, 80*10*3, at 23°C) ¹¹ | 8 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*3, at -30°C) ¹¹ | 5 | kJ/m² | ISO 180/1A |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*3 sp=62mm) ¹¹ | 8 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*3 sp=62mm) ¹¹ | 5 | kJ/m² | ISO 179/1eA |
| Izod Impact (Notched, at 23°C) ¹¹ | 213 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 47 | J | ASTM D3763 |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 14 | kJ/m² | ISO 180/1A |
Table 6 of 7
23 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 80 - 90 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time ⁷ | 2 - 4 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.04 | % |
| Maximum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 245 - 275 | °C |
| Melt Temperature ⁷ | 230 - 270 | °C |
| Nozzle Temperature ⁷ | 245 - 275 | °C |
| Nozzle Temperature ⁷ | 220 - 260 | °C |
| Front - Zone 3 Temperature ⁷ | 245 - 275 | °C |
| Front - Zone 3 Temperature ⁷ | 230 - 270 | °C |
Table 7 of 7
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized (94-5VB Flame Class Rating) ᵖ | min. 2 | mm | UL 94 |
| UL Recognized (94V-0 Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
| UL Recognized (94V-1 Flame Class Rating) ᵖ | min. 1.2 | mm | UL 94 |
| UL Recognized (94V-2 Flame Class Rating) ᵖ | min. 1 | mm | UL 94 |
| Oxygen Index (LOI) ᵖ | 32 | % | ISO 4589 |
