Jaylink Additives® JL-106E

CASE Ingredients Features: Abrasion ResistanceChemical ResistanceFast CureHigh Impact ResistanceImproved Hardness

Jaylink Additives® JL-106E polymerizable cellulosic is an acrylamidomethyl—substituted cellulose ester polymer. Due to its high degree of acrylamide substitution, formulations using JL-106E cure very rapidly in response to UV/EB. Resulting films have excellent abrasion, chemical, and impact resistance. The hydrophobic and hydrophilic segments of 106E make it an excellent compatibilizer for materials of differing polarity. JL-106E is used for its thixotropic characteristics, which are particularly useful in improving UV ink holdout on porous substrates, without sacrificing cured properties. This material is INCI listed for use in the cosmetic industry

Identification

Chemical Family: Cellulose & Cellulosics, Urethane Acrylate/IsocyanateCellulose & CellulosicsUrethane Acrylate/Isocyanate
CASE Ingredients Functions: Rheology ModifierThickenerThixotrope

Product families

CASE Ingredients — Additives

Rheology Modifiers & Stabilizers

Other characteristics

Brand: Jaylink Additives
Functions: Rheology Modifier, Thickener, Thixotrope
Features: Improves impact resistance
Accelerates cure
Enhances surface hardness
Mild thixotrope
Provides chemical resistance
Low -haze
Appearance: White Powder
Applications: UV/EB coatings
Rheological additive
Fiberglass composites
Technology: CASE Ingredients
Formulation Notes: JL-106E is typically used at 2-10% by weight in most applications. When used in a formulation, it is most easily incorporated by making a concentrate out of the monomer in the formulation with the strongest solvency. Stir the monomer with a shear (Cowles-type) mix blade, and heat (up to 60°C). Sift the JL-106E into the vortex of the mixing monomer, so as to prevent agglomeration. Mix until the powder dissolves fully. Typically, a 25 to 50% solution is feasible, depending on the monomer solvency. This concentrate is then added to the formulation (in the case of inks, on the letdown side, before blending with the grind). Once dissolved, JL-106E is very compatible with most oligomers, monomers, photoinitiators, and additives. JL-106E is soluble in most acetate and ketone solvents, along with acrylate monomers, such as IBOA, NNDMA, NVP, EOEOEA, TMPTA, GPTA, PONPGDA, HDDA, and TPGDA.
General Information: This product is intended for industrial use only. Keep out of the reach of children. Avoid breathing vapors. Avoid contact with skin, eyes, and clothing. Wear impervious gloves. Repeated or continuous skin contact with uncured material may cause irritation. Remove material from skin with soap and water. Never use organic solvents to remove material from skin and eyes. For more information on the safe handling of this material, please refer to the Safety Data Sheet before use.
Typical Formulations: ** Per ASTM D882 – Not Tested || Incompatible X Unable to Measure; Typical Formulations; * Brookfield – CAP 2000+ @ 25°C.; Adhesion Properties; Cold Rolled Steel; X Recommended XX Highly Recommended XXX Strongly Recommended
Compatible Substrates and Surfaces: Fiberglass

Technical data

Table 1 of 3

2 rows

Characteristic	Value
Fluorescing	Blue
Rheology	Newtonian

Table 2 of 3

5 rows

Characteristic	Value	Unit
Durometer Hardness	D70	—
Elongation at Break	160.0	%
Modulus of Elasticity	359 [52,170]	MPa (psi)
Nominal Viscosity	150.0	cP
Tensile at Break	3200.0	MPa (psi)

Table 3 of 3