NORYL™ Resin GFN30F

Name: NORYL™ Resin GFN30F
Brand: NORYL™ Resin

SABIC's Specialties Business NORYL™ GFN30F resin is a 30% glass fiber reinforced blend of polyphenylene ether (PPE) + polystyrene (PS). This injection moldable grade exhibits very low moisture absorption, high strength, hydrolytic stability, Low warpage, low specific gravity, and dimensional stability. NORYL™ GFN30F carries a UL746C outdoor suitability rating of F2 along with FDA food contact compliance and NSF 61 listings in several colors. The properties of this material makes it an excellent candidate for water management applications such as water filter and meter components, pump housings / impellers, shower + faucet, and valves.*See NORYL™ GFN30 resin for NON FDA / NSF version. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.

Product families

Applications

Building & Construction — Building Materials

Pipes & Plumbing

Industrial — Power, Water & Utilities

Water Treatment

Product Families

Plastics — Engineering & Specialty Polymers

Blends & Alloys

Other characteristics

Brand: NORYL™ Resin
Density: 1310.0 - 1310.0 kg/m³
Polymer Name: PPO/PS Alloy
Flexural Modulus: 6800.0 - 6800.0 MPa
Processing Methods: Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Building & Construction
Industrial
Flame Rating: UL 94 HB
Technology: Plastics
Labeling Claims: Food Contact Acceptable
No Added PFAS
Fillers Included: Glass Fiber
Additives Included: Mold Release Agent
Material Features: Amorphous
Dimensional Stability
Excellent Stiffness
Food Contact Acceptable
Good Mold Release
Good Stiffness
High Hydrolytic Stability
High Stiffness
Country Availability: China (Mainland)
Certifications and Compliance: NSF Standard 61 for Drinking Water
UL 94
Plastics and Elastomers End Uses: Faucet System Components
Filters
Fittings
Gears
Hygiene
Potable Water Applications
Pump Parts
Water Management
Plastics and Elastomers Functions: Resin
Plastics and Elastomers Processing Methods: Injection Molding

Technical data

Table 1 of 7

10 rows

Characteristic	Value	Unit	Method
Tensile Stress (Break, Type I, 50 mm/min) ¹¹	130	MPa	ASTM D638
Tensile Strain (Break, Type I, 50 mm/min) ¹¹	3	%	ASTM D638
Tensile Modulus (at 5 mm/min) ¹¹	8600	MPa	ASTM D638
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹	160	MPa	ASTM D790
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	7200	MPa	ASTM D790
Tensile Stress (Break, 50 mm/min) ¹¹	110	MPa	ISO 527
Tensile Strain (Break, 50 mm/min) ¹¹	2.5	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	8200	MPa	ISO 527
Flexural Stress (Yield, at 2 mm/min) ¹¹	160	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	6800	MPa	ISO 178

Table 2 of 7

6 rows

Characteristic	Value	Unit	Method
Specific Gravity ¹¹	1.31	—	ASTM D792
Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹	0.1 - 0.4	%	SABIC method
Melt Flow Rate (at 280°C, 5.0 kgf) ¹¹	3.2	g/10 min	ASTM D1238
Water Absorption (at 23°C, saturated) ¹¹	0.1	%	ISO 62-1
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.04	%	ISO 62
Melt Volume Rate (at 280°C, 5.0 kg) ¹¹	2	cm³/10 min	ISO 1133

Table 3 of 7

13 rows

Characteristic	Value	Unit	Method
Vicat Softening Temperature (Rate B/50) ¹¹	147	°C	ASTM D1525
Vicat Softening Temperature (Rate B/50) ¹¹	147	°C	ISO 306
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	147	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	139	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.000021	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.000023	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.000075	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.00007	1/°C	ISO 11359-2
Vicat Softening Temperature (Rate B/120) ¹¹	149	°C	ISO 306
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	139	°C	ISO 75/Af
Relative Temperature Index (Electrical) ᵖ ¹¹	90	°C	UL 746B
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹	90	°C	UL 746B

Table 4 of 7

5 rows

Characteristic	Value	Unit	Method
Comparative Tracking Index (UL, PLC) ¹¹	4	PLC Code	UL 746A
High Ampere Arc Ignition (PLC 4) ¹¹	min. 1.5	mm	UL 746A
Hot Wire Ignition (PLC 0) ¹¹	min. 1.5	mm	UL 746A
High Voltage Arc Track Rate (PLC) ¹¹	3	PLC Code	UL 746A
Arc Resistance (Tungsten, PLC) ¹¹	6	PLC Code	ASTM D495

Table 5 of 7

8 rows

Characteristic	Value	Unit	Method
Izod Impact (Unnotched, at 23°C) ¹¹	590	J/m	ASTM D4812
Izod Impact (Notched, at 23°C) ¹¹	100	J/m	ASTM D256
Izod Impact (Notched, at -30°C) ¹¹	120	J/m	ASTM D256
Instrumented Dart Impact Total Energy (at 23°C) ¹¹	20	J	ASTM D3763
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	30	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80104, at 23°C) ¹¹	11	kJ/m²	ISO 180/1A
Izod Impact (Notched, 80104, at -30°C) ¹¹	10	kJ/m²	ISO 180/1A
Charpy Impact (at 23°C, V-notch Edgew 80104 sp=62mm) ¹¹	8	kJ/m²	ISO 179/1eA

Table 6 of 7