Imper-Sol™ EB All-In-One Roof Coatings
Imper-Sol™ EB All-In-One Roof Coatings is a unique rubber coating that provides extremely effective protection, reducing costly reapplications. It is a one component product that has excellent adhesion to properly prepared surfaces. It controls corrosion and rust bleed through, even after years of service. It is thermally stable and resists cracking and peeling due to weather extremes and ultraviolet exposure.
Product families
Applications
- Wood Coatings & Finishes
- Waterproofing & Weatherproofing
Product Families
- Protective Coatings
Other characteristics
- Brand
- Imper-Sol
- Features
Cost Effective, Crack Resistant, Good Thermal Stability, Long Term Protection, Low Corrosion, Peel Resistance
- Product Type
- Coating
- Application Area
- Roofing Membranes
- Application Method
- Brush, Roller, Spray
- Compatible Substrates & Surfaces
- Metal, Wood
- Markets
- Building & Construction
- Paints & Coatings
- Application
Metal Buildings and Roofs; Modified and BUR Roofs; Urethane Foam Roofs; Single Ply Roofs; The surface must be free of any dirt, moisture, oils, algae or other contaminates that may interfere with good adhesion. Carefully remove any loose material from surface with a wire brush or scraper. Grease and oil should also be removed with environmentally safe solvents or an appropriate detergent cleaner such as Imper-Sol Cleaner Degreaser. In most cases a high pressure water blast will be sufficient to prepare the surface.; For best results, the temperature of the ambient air and the substrate should be within a range of 50°-100°F. For best spray application, the product should be at a minimum of 60°F. Lower temperatures can be utilized for brush applications.; Imper-Sol EB All-in-One can be applied by brush, spray or roller. Best re-sults can be obtained with airless spray equipment. See BITEC Application Bulletins for additional information.
- Technology
- Ready-to-Use Products
- Wet Adhesion
- Wet Adhesion
- (ASTM C794/D903)
- Metal
- Pass
- SBS Mod. Bit
- APP Mod. Bit
- Smooth BUR
- EPDM
- Application Methods
- Brush
- Roller
- Spray
- Handling
Imper-Sol EB All-in-One vehicle is a blend of solvents considered combustible by the standards of the D.O.T. and O.S.H.A. Keep away from heat, open flame, or sparks. Use in a well ventilated area.. Notice: It should be used and stored away from flames, in a well-ventilated atmosphere. Avoid prolonged breathing of vapors and prevent contact with eyes. Read all label information, SDS, and precautions before using. The specifications, properties and performance of materials described herein are based on information believed to be reliable. Unless otherwise expressly provided in written contract, the products discussed are sold without conditions or warranties, expressed or implied. Product specifications are subject to change without notice.
- Ready to Use Product Features
- Cost Effective
- Crack Resistant
- Good Thermal Stability
- Long Term Protection
- Low Corrosion
- Peel Resistance
- Compatible Substrates and Surfaces
- Metal
- Wood
Technical data
Table 1 of 1
16 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Coverage Rate | 80 - 100 | ft²/gal | — |
| Viscosity (78˚F) | 9900.0 | cP | — |
| Drying Time | 2 - 4 | hours | — |
| Elongation | 500.0 | % | ASTM D412 |
| Tensile Strength | 1520.0 | psi | ASTM D412 |
| Permeance (10mils) | 0.166 | perms | ASTM E96 |
| Fungi Resist | 0 Pass | — | ASTM G21 |
| H₂O Swell | 0.0 | % | ASTM D471 |
| Weathering | Pass | — | ASTM 4798 |
| Weight | 8.5 l | lb/gal | — |
| Flash Point | 101.0 | ˚F | — |
| Low Temperature Flex | Pass | — | ASTM D522 |
