AMP-UP™ URETHANE
- Chemical Family
- Urethanes
AMP-UP™ URETHANE is a two component, high build acrylic aliphatic urethane with excellent color and gloss retention. Finish cures to a very tough, abrasive resistant film with exceptional exterior durability, chalk resistance, color stability and longterm gloss retention. AMP-UP™ URETHANE will not degrade when exposed to the alkali on a construction site. Acids and detergents will not stain. This product was developed for use on aluminum, as well as structural steel for both interior and exterior applications. Available in a full range of colors and a satin finish.
Product families
Applications
- Paints & Coatings — Other Paints & Coatings Applications
- Architectural Coatings
- Automotive OEM Coatings
- Industrial Coatings
Product Families
- Other Paints & Coatings
Other characteristics
- Brand
- AMP-UP
- Features
Abrasion Resistant, Chemical Resistant, Corrosion Resistant, Excellent Chalk Resistance, Good Color Stability, Good Gloss Retention, High Impact Resistance, Improved Flexibility, Low Odor, Outdoor Durability, Stain Resistant
- Product Type
- 2K (2 component) Coating
- Application Method
- Brush, Roller, Spray
- Compatible Substrates & Surfaces
- Concrete, Metal, Steel
- Markets
- Automotive & Transportation
- Building & Construction
- Paints & Coatings
- PACKAGING
- 1.25-Gallon Kit
- 5-Gallon Kit
- Shelf LIfe
- 1 Year, 1 year
- Technology
- Ready-to-Use Products
- Labeling Claims
- Environmentally Friendly
- Low VOC
- Application Methods
- Brush
- Roller
- Spray
- Primers
This topcoat is compatible with a wide range of primers. Excellent performance will be obtained when used with any of the AMP-UP™ Series products.
- Surface Preparation
- Primer Surface
- When applying this product at topcoat on the AMPUP ™ Series products, it is essential to remove all contamination that can affect coating application and interfere with coating adhesion. Inspect the surface of the primer before applying this product and remove dirt, dust, oil, salt, and any other chemical contaminants by washing the surface with a cleaner/degreaser. Mold and mildew areas must be cleaned with a chlorinated cleaner or bleach solution. Rinse thoroughly with fresh water and allow to fully dry. All surfaces must be dry at time of application. Paint solvent should not be used for cleaning or degreasing the primer surface. Verify with technical data sheet and application guide of the AMP-UP™ Series products for overcoatability and the given maximum over-coating interval.
- Previously Coated
- Previously coated surfaces must be in good condition. Smooth, hard or glossy finishes should be sanded to create a surface profile. To ensure product compatibility, application on a test patch is recommended.
- Equipment Recommendations
Brush: Use a good quality synthetic bristle brush such as Purdy® brush.; Roller: Use a good quality synthetic nap.; Air-Atomized Spray:; Air cap for highest pressure; Airless Spray:; THINNING Thinner 1 (Fast) or Thinner 2 (Slow) The choice of correct thinner will give optimum lay down of product and ease of application Depending on temperature and humidity, select the thinner and the degree of thinning. Thinner 1 is recommended for brush and roll applications. Thinner 2 is recommended for spray applications.; CLEAN-UP: Use xylenes or MEK after use.
- Ready to Use Product Features
- Abrasion Resistant
- Chemical Resistant
- Corrosion Resistant
- Excellent Chalk Resistance
- Good Color Stability
- Good Gloss Retention
- High Impact Resistance
- Improved Flexibility
- Compatible Substrates and Surfaces
- Concrete
- Metal
- Steel
Technical data
Table 1 of 1
14 rows| Characteristic | Value | Unit |
|---|---|---|
| Dry Times (25°C) | 2 - 3 | hours |
| Dry Times (70°C) | 30 | minutes |
| Coverage at Recommended DFT | 250 - 300 | sq. ft./gal. |
| Mix Ratio Part A (by Volume) | 4 | Parts |
| Mix Ratio Part B (by Volume) | 1 | Parts |
| Pigment Type | Metal Oxides | — |
| Pot Life (70-80°F, 50% Relative Humidity) | 3 - 4 | hours |
| Recommended Dry Film Thickness (DFT) Per Coat | 2 | mils |
| Resin Type | High Solids Polyurethane | — |
| Solids (By Volume) | 60 - 70 | % |
| Solvents | Xylenes, Methyl Amyl Ketone | — |
| Mix Ratio Thinner 1/2 (by Volume) | 1 part | — |
