Optus Trawlerdek
Optus Trawlerdek is a heavy duty screed system for marine and offshore applications. This solvent free epoxy resin weatherdeck screed was specifically developed for workboat and navy applications. It is durable, resistant to abrasion and will withstand heavy loads. It is supplied in 3 components, trowel applied.
Product families
Applications
- Marine Coatings
- Marine
Product Families
- Protective Coatings
Other characteristics
- Features
Chemical Resistant, Cost Effective, Durable, Excellent Substrate Adhesion, Excellent Toughness, High Impact Resistance
- Product Type
- Solventless & High Solids Coating
- Compatible Substrates & Surfaces
- Metal, Steel
- Markets
- Automotive & Transportation
- Benefits
- Tough and durable
- Seamless
- Impermeable
- Low maintenance
- Resistance to chemicals and cleaning products.
- Impact resistant, withstands heavy loading.
- Excellent adhesion to prepared substrates.
- Allows for movement of substrates.
- PACKAGING
Supplied 29.5 kg units and 3 Components. Packaging is in 1litre and 5litre pots and 25kg bag.
- Technology
- Ready-to-Use Products
- Packaging Type
- Bags
- Labeling Claims
- Solvent-free
- Coverage and Cure
A 29.5kg unit of Trawlerdek will cover approximately 2.5m2 at thickness of 5mm.; Curing times : Initial set @ 20°C- 8 hours; Open to traffic @ 20°C- 24 hours
- Application Procedure
Ambient temperature should be between 5°C and 30°C during application and cure. Dry weather conditions and a dry substrate are essential.; Steel- Remove all rust, mill scale and surface contamination by grit blasting and other mechanical means to a bright rust free surface (SA2½). Oil and grease contamination should be removed with a suitable cleaning fluid and the residue flushed off with water Allow to dry thoroughly.; Priming- To avoid flash rusting of prepared surfaces, it may be necessary to apply a holding primer. This must be compatible with Resitech MP Primer. Coat with an application of Resitech MP Primer. The primer is supplied in pre-weighed packages. It is essential that all of the curing agent, Pack A, is added to all of the resin component, Pack B, and that it is then mixed thoroughly for 60 seconds with a mechanical paint stirrer. When fully mixed, the primer should be applied immediately to the prepared substrate by brush or roller. The coverage rate of the primer is dependent upon the texture and porosity of the substrate, but will be in the range of 4-6m2 /liter.; Mixing and application- Trawlerdek is a 3 component system which is supplied in pre-weighed packages. It is essential that all of the curing agent, pack A, is added to all of the resin component, pack B, and mixed thoroughly in a forced action mixing vessel (pennine, daines, mixal or similar) for about 3 minutes. The graded filler component, pack C, is then gradually added whilst mixing continues for an additional three minutes. The fully blended system is applied in one application, at the specified thickness, onto the wet primer using a steel trowel in order to obtain a tight, uniform surface appearance.
- Ready to Use Product Features
- Chemical Resistant
- Cost Effective
- Durable
- Excellent Substrate Adhesion
- Excellent Toughness
- High Impact Resistance
- Compatible Substrates and Surfaces
- Metal
- Steel
Technical data
Table 1 of 1
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Adhesion to Steel (Pull-off Test at 5 days) | 5.0 | N/mm2 | BS 24624:1993 |
| Elongation at Break (After Curing for 14 days in Air) | min. 7 | % | BS 2782 Pt3 |
| Relative Density (20°C) | 2.2 | — | — |
| Tensile Strength (After Curing for 14 days in Air) | 20.0 | N/mm2 | BS 2782 Pt3 |
