Kardol EPOXY GLUE
- Chemical Family
- Epoxy & Epoxy Derivatives
Kardol Epoxy Glue is an exceptional adhesive will bond to almost any surface such as cement, fiberglass, wood, aluminum, steel and styrofoam.
Product families
Applications
- Equipment & Parts
- Marine
Product Families
- Structural Adhesives
Other characteristics
- Product Type
- 2K (2 component) Adhesive, Epoxy Adhesive
- 2K (2 component) Adhesive
- Epoxy Adhesive
- Compatible Substrates & Surfaces
- Aluminum, Metal, Steel, Wood
- Markets
- Automotive & Transportation
- Industrial
- Technology
- Ready-to-Use Products
- Ready to Use Product Features
- Good Compressive Strength
- Good Flexural Modulus
- High Tensile Strength
- Compatible Substrates and Surfaces
- Aluminum
- Metal
- Steel
- Wood
- Epoxy Glue DO'S and DON'T's
Do's; Use epoxy glue when surface to be repaired is at least 65°. Please remember that it is possible for air temperature to be 80° and the surface to be repaired can maintain a temperature of 60°. We suggest warming surface with a heat lamp or placing it in direct sunlight to assure a minimum 65° temperature.; After repair has been made, and a minimum of 24 hours has passed, you still have a tacky surface, you may remove the tackiness with Kardol acetone.; Cure time may be lessened by using an electric hair dryer.; Kardol Epoxy Glue Part 1 and Part 2 should be mixed together for approximately 3 minutes to assure thorough mixing.; Kardol Epoxy Glue may be applied with a brush, notched trowel, plastic spreader etc. Kardol Epoxy Glue should have a glue line of 10-20 mils thickness; approximately as thick as a standard business card (1/64).; Kardol Epoxy Glue may be mixed with washed sand, colored or plain , to form a grout or mortar. Mix 50% -75% by volume. Clean up with Kardol Toluene or Kardol Multi-Purpose Lacquer Thinner.; Always use rubber surgical gloves when working with Kardol Epoxy Glue.; DON'T'S; Use Epoxy Glue when outside temperature is below 60°F.; Apply to polypropylene, polyethylene or rubber. Kardol Epoxy Glue may be used on PVC pipe after the surface has been sanded with a minimum 40 grit sandpaper and cleaned with; Kardol acetone.; When clamping, do not squeeze out glue – use toothpicks to prevent extensive pressure from displacing glue.; Never leave caps or lids off containers. Epoxies attract moisture which will cause glue to have a slow cure and a tacky surface.
- Typical Properties (Cured)
Curing Temperature; Lap Shear Strength (Alclad 2024-T-3 aluminum degreased and acid etched per ASTM-D-2651 and tested according to ASTM-D-1002.)
Technical data
Table 1 of 3
3 rows| Characteristic | Value | Unit |
|---|---|---|
| Pot Life | 45.0 | minutes |
| Specific Gravity (25°C) | 1.19 | — |
| Sag Resistancem (25°C, 1 ½”) | Pass | — |
Table 2 of 3
14 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Deflection Temperature (264 psi, Cured 7 days) | 45.5 | °C | ASTM-D-648 |
| Compressive Strength (25°C, Ultimate, Cured 7 days) | 10.8 | kg/mm2 | ASTM-D-695 |
| Compressive Strength (25°C, Yield, Cured 7 days) | 4.0 | kg/mm2 | ASTM-D-695 |
| Compressive Strain (25°C, Ultimate, Cured 7 days) | 49.0 | % | ASTM-D-695 |
| Compressive Strain at Yield (25°C, Yield, Cured 7 days) | 2.0 | % | ASTM-D-695 |
| Modulus of Elasticity (Compressive, 25°C, Cured 7 days) | 204.0 | kg/mm2 | — |
| Tensile Stress (Ultimate, 25°C, Cured 7 days) | 3.6 | kg/mm2 | ASTM-D-638 |
| Modulus of Elasticity (Tensile, 25°C, Cured 7 days) | 190.0 | kg/mm2 | ASTM-D-638 |
| Tensile Elongation (at failure, 25°C, Cured 7 days) | 6.5 | % | ASTM-D-638 |
| Flexural Strength (25°C, Cured 7 days) | 5.4 | kg/mm2 | ASTM-D-790 |
| Modulus of Elasticity (25°C, Cured 7 days) | 190.0 | kg/mm2 | ASTM-D-790 |
| Water Absorption (Weight gain, 24 hrs immersion at 25°C) | 0.3 | % | ASTM-D-570 |
Table 3 of 3
3 rows| Characteristic | Value |
|---|---|
| Mixing Ratio (Volume) | 1:1 |
| Mixing Ratio (Weight) | 1900-01-03 |
| Mixed Sag Resistance (25°C, 1 ½”) | Pass |
