Pro-935 R-35® Adhesion Promoting Primer
Pro-935 R-35® Adhesion Promoting Primer is an adhesion promoting clear acrylic wallcovering primer. Ideal for non-porous surfaces, such as ceramic tile, formica, and glass. PRO-935 dries with a permanent tack, allowing for wallcovering to be installed over hard to adhere to sealed surfaces
Product families
Applications
- Architectural Coatings
Product Families
- Primers & Sealers
Other characteristics
- Brand
- Pro-935 R-35
- Features
- Good Adhesion, Low Odor, Mildew Resistant, Tacky
- Dries clear with a permanent tack
- Water resistant
- Low odor, no spatter
- Product Type
- Primer
- Application Method
- Roller, Spray
- Compatible Substrates & Surfaces
- Ceramic, Wood
- Caution
Do not take internally. In case of ingestion, seek medical attention. Avoid contact with skin and eyes. Use of skin and eye protection is recommended at all times. If contact with eye occurs, flush with water for 15 minutes. If skin contact occurs, wash with soap and water. Seek medical attention if rash or other symptoms occur. Do not mix with other chemicals. Use in a well-ventilated work area. Close container after each use. Keep out of reach of children.
- Markets
- Building & Construction
- Storage
- Store in a cool, dry place. Do Not Freeze!
- Warning
If you scrape, sand, or remove old paint, you may release lead dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as brain damage, especially in children. Pregnant women should also avoid exposure. Wear a niosh-approved respirator to control lead exposure. Clean up carefully with a hepa vacuum and a wet mop.
- Application
- Recommended Uses
- Application over non-porous or sealed surfaces.
- Not Recommended For
- Porous surfaces. Not recommended for direct application over oil-based primers.
- Compatible Coatings
- All ROMAN® adhesives
- Substrates
- Non-porous surfaces such as ceramic tile, sealed wood paneling and glass/mirrors
- Mildew-Resistant
- All Roman products contain biocides for in-can preservation
- Technology
- Ready-to-Use Products
- Application Methods
- Roller
- Spray
- Specification Data
- Coverage
- Up to approx. 400-450 square feet per gallon
- Drying Time
- Minimum drying time is three hours. Optimum drying time is 12 hours. Low temperature, high humidity and poor ventilation will slow down the drying process.
- Application Instructions
Surface Preparation: Surface must be free from grease and all residues, dry, smooth and structurally sound. Repair all unsound surfaces. Clean ceramic tile, paneling, glass and sealed surfaces with isopropyl alcohol. For best results, lightly sand or abrade all glossy or sealed surfaces prior to applying. Before proceeding with any unusual conditions, consult your adhesive or wallcovering supplier.; After completion of the required surface preparation, it is critical to test the surface to ensure compatibility. Select a small, inconspicuous area of the surface for testing and apply the primer or adhesive as specified. Inspect test area after 24 hours before proceeding with installation of wallcovering.; Dilution: Do not dilute.; Application Method: Use only when the room temperature is above 60ºF. Apply at recommended spread rate using roller or spraying system. Do not overspread.; Airless Spray:; minimum 3000 PSI; Clean-Up: Before the primer dries, remove any excess with clean water. Brushes and rollers should be cleaned immediately after use with a mild soap and clean, warm water.
- Ready to Use Product Features
- Good Adhesion
- Low Odor
- Mildew Resistant
- Tacky
- Compatible Substrates and Surfaces
- Ceramic
- Wood
Technical data
Table 1 of 1
3 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| pH Level | 9.3 | — | — |
| Viscosity | approx. 1,600 | cps | — |
| VOC (Regulatory) | 0.0 | g/L | EPA Method 24 |
