Fluon+™ LM-ETFE AH-3000
- CASE Ingredients Features
- Crack ResistanceExcellent AdhesionImproved Ageing ResistanceImproved FlexibilityImproved WorkabilityTransparencyWeather Resistance
- Chemical Family
- Fluoropolymers
AGC Chemicals Americas, Inc. Fluon+™ LM-ETFE AH-3000 is a semiconductive modified copolymer of ethylene and tetrafluoroethylene used in applications where strong adhesion to polyamide polymers, especially nylon 12, is required. It also exhibits high permeation resistance to many fluids and gasses, especially automotive fuels. It is processed using conventional melt extrusion methods and is available as a 1/8” pellet.
Properties
- Physical Form
- Pellets
- Solid
Identification
- CASE Ingredients Functions
- Binder & Resin
Other characteristics
- Brand
- Fluon+
- Polymer Name
- Ethylene Tetrafluoroethylene Copolymer (ETFE)
- Processing Methods
Blow Molding, Coextrusion, Compression Molding, Extrusion, Injection Molding, Transfer Molding
- Markets
- Automotive & Transportation
- Industrial
- Storage
The properties of Fluon LM-ETFE are not impacted by storage time. Storage and handling facilities should be designed to minimize contact with airborne contamination and the formulation of condensation on the resin. Fluoropolymers are not hydroscopic and will not typically need to be dried prior to use. However, masterbatches used to pigment fluoropolymers may contain materials that do absorb water and should be dried prior to use.
- Processing
Fluon LM-ETFE fluoropolymer resins can be processed using conventional melt processable techniques including extrusion, injection molding, blow molding, compression molding, and transfer molding. It is strongly recommended that process equipment exposed to molten resin be made of corrosion-resistant metals such as Monel, Inconel, or Hastelloy.. Extruder barrels should be long relative to diameter (24/1 to 30/1 and beyond) and heaters should have adequate capacity to heat the material to approximately 340°C. Temperature controllers should be of the proportional-integral derivative (PID) type to insure precise temperature control. Extruder screws with a 3/1 compression ratio, a relatively long feed zone, and a ½ to 3 turn transition zone are recommended.
- Technology
- CASE Ingredients
- Plastics
- Labeling Claims
- Non-Flammable
- Material Features
Good Adhesion; Good Environmental Stress Crack Resistance (ESCR); Permeation Resistant
- Certifications and Compliance
- FDA Compliant
- Compatible Polymers and Resins
- Polyamide 12 (PA12)
- Polyamides
- Plastics and Elastomers End Uses
- Automotive Fuel Structural Components
- Conveyor Parts
- Hoses
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Blow Molding
- Coextrusion
- Compression Molding
- Extrusion
- Injection Molding
- Transfer Molding
Technical data
Table 1 of 1
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Adhesion to PA12 | 60 | N/cm | Initial |
| Flexural Modulus | 1220 | MPa | ASTM D-790 |
| Izod Impact Strength (at 23°C) | No Break | J/m | ASTM D-256 |
| Melt Flow Rate | 20 | g/10 min | ASTM D-3307 |
| Melting Point | 240 | °C | DSC |
| Permeation Rate (CE10, at 60°C) | 2 | g-mm/m²-day | JIS Z0208 (CUP) |
| Specific Gravity | 1.77 | — | ASTM D-792 |
| Surface Resistivity | 1 x 10³ | Ω/square | AGC Method |
| Tensile Elongation | 350 | % | ASTM D-638 |
| Tensile Strength | 36 | MPa | ASTM D-638 |
