Fluon® ETFE AH-3000L
- Chemical Family
- FluoropolymersPolyolefins
AGC Chemicals Americas, Inc. Fluon® ETFE AH-3000L is a semiconductive, modified copolymer of ethylene and tetrafluoroethylene. It is used in applications where superior stress-cracking properties and strong adhesion to polyamide polymers, especially nylon 12, are required. This product also exhibits high permeation resistance to many fluids and gasses, especially automotive fuels. It is processed using conventional melt extrusion methods and is available as a 1/8” pellet.
Properties
- Physical Form
- Pellets
- Solid
Product families
Applications
- Cooling & Climate
- Fuel Systems
Product Families
- High Performance Thermoplastics
Other characteristics
- Brand
- Fluon
- Polymer Name
- Ethylene Tetrafluoroethylene Copolymer (ETFE)
- Flexural Modulus
- 1290.0 - 1290.0 MPa
- Additives Included
- Thermal Stabilizer
- Processing Methods
- Extrusion
- Markets
- Automotive & Transportation
- Storage
The properties of Fluon LM-ETFE are not impacted by storage time. Storage and handling facilities should be designed to minimize contact with airborne contamination and the formulation of condensation on the resin. Fluoropolymers are not hydroscopic and will not typically need to be dried prior to use. However, masterbatches used to pigment fluoropolymers may contain materials that do absorb water and should be dried prior to use.
- Processing
Fluon LM-ETFE fluoropolymer resins can be processed using conventional melt processable techniques including extrusion, injection molding, blow molding, compression molding, and transfer molding. It is strongly recommended that process equipment exposed to molten resin be made of corrosion-resistant metals such as Monel, Inconel, or Hastelloy.. Extruder barrels should be long relative to diameter (24/1 to 30/1 and beyond) and heaters should have adequate capacity to heat the material to approximately 340°C. Temperature controllers should be of the proportional-integral derivative (PID) type to insure precise temperature control. Extruder screws with a 3/1 compression ratio, a relatively long feed zone, and a ½ to 3 turn transition zone are recommended.
- Technology
- Plastics
- Material Features
- Excellent Flexibility
- Excellent Transparency Properties
- Good Thermal Stability
- Low Gas Permeability
- Low Melting Point
- Smooth Surface Finish
- Product Development
This data was secured during the course of product development. Both the properties and the product are subject to change prior to final commercialization.
- Handling Precautions
WARNING: Vapors that can be hazardous if inhaled may be liberated during processing.. Please consult the Material Safety Data Sheet for Fluon LM-ETFE prior to use. It is also recommended that the user consult the latest edition of the "Guide to the Safe Handling of Fluoropolymer Resins" published by the Fluoropolymers Division of the Society of the Plastics Industry (SPI) for important handling and ventilation recommendations. Both publications are available from your AGC Chemicals Americas representative.
- Compatible Polymers and Resins
- Polyamide 12 (PA12)
- Plastics and Elastomers End Uses
- Hoses
- Tubing
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Extrusion
Technical data
Table 1 of 1
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Adhesion to PA12 (Initial) | Impossible to Peel | N/cm | AGC Method |
| Flexural Modulus | 1290 | MPa | ASTM D-790 |
| Izod Impact Strength (at 23°C) | No Break | J/m | ASTM D-256 |
| Melt Flow Rate | 6 | g/10 min | ASTM D-3307 |
| Melting Point | 234 | °C | DSC |
| Permeation Rate (CE10, at 60°C) | 2 | g-mm/m²-day | JIS Z0208 (CUP) |
| Specific Gravity | 1.76 | — | ASTM D-792 |
| Surface Resistivity | 6.9 x 10³ | Ω/square | AGC Method |
| Tensile Elongation | 370 | % | ASTM D-638 |
| Tensile Strength | 40 | MPa | ASTM D-638 |
