Fluon® PFA P-62XP
- Chemical Family
- Fluoropolymers
AGC Chemicals Americas, Inc. Fluon® PFA P-62XP (perfluoroalkoxy) is a melt-processible copolymer of tetrafluoroethylene and a perfluorinated vinyl ether. Fluon® PFA P-62XP has chemical, electrical, and thermal properties almost identical to its close chemical cousin, polytetrafluoroethylene (PTFE), yet can be processed by conventional extrusion, injection molding, blow molding, and transfer molding techniques. This unique material can be used over a wide range of temperatures (-200°C to 260°C). It is available as a 1/8 inch pellet.
Properties
- Physical Form
- Pellets
- Solid
Product families
- High Performance Thermoplastics
Other characteristics
- Brand
- Fluon
- Polymer Name
- Perfluoroalkoxy Polymer (PFA)
- Flexural Modulus
- 699.335 - 699.335 MPa
- Processing Methods
- Extrusion, Injection Molding
- Markets
- Agriculture & Feed
- Automotive & Transportation
- Building & Construction
- Electrical & Electronics
- Benefits
High Resistance to Heat; Excellent Chemical Resistance; Low Smoke and Flame Characteristics. Fluon® PFA is rated 94V-0 by; Underwriters Laboratories Inc.; Outstanding Resistance to Weather and Aging; Excellent Dielectric Properties; Non-Stick Characteristics
- Processing
Fluon PFA fluoropolymer resins can be processed by conventional melt-processable resin techniques including extrusion, injection molding, blow molding, compression molding, transfer molding, and rotolining/rotomolding. It is strongly recommended that process equipment exposed to molten resin be made of corrosion-resistant metals such as Monel®, Inconel®, or Hastelloy®.; Extruder barrels should be long relative to diameter (24/1 up to 30/1 and beyond) and heaters should have the capacity to heat material to approximately 390ºC. Temperature controllers should be of the proportional-integral-derivative (PID) type to insure precise temperature control. Extruder screws with 3/1 compression ratio, a relatively long feed zone, and ½ to 3 turn transition zone are recommended.; Your AGC Chemicals Americas, Inc. technical service representative can provide specific recommendations for process equipment and process conditions.
- Flame Rating
- UL 94 V0
- Technology
- Plastics
- Material Features
- Chemical Resistant
- Excellent Dielectric Properties
- Good Aging Behavior
- Good Weather Stability
- High Flow
- Low Smoke Emission
- Non Stick
- Very Good Heat Resistance
- ASTM Classification
Fluon PFA grade P-63P is classified as ASTM D-3307 Type I; grade P-66P is classified as ASTM D-3307 Type II; and grade P-65P is classified as ASTM D-3307 Type III. Your AGC Chemicals Americas representative can advise you of the ASTM classifications of the other PFA materials.
Technical data
Table 1 of 1
23 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| CLTE (0 – 100ºC) | 7.2 x 10⁻⁵ | in/in/ºF | D-696 |
| Dielectric Constant (at 1mHz, 23°C) | 2.07 | — | D-150 |
| Dielectric Strength (at 10 mil film) | 1900 | volts/mil | D-149 |
| Flame Rating | V-0 | — | UL-94 |
| Flexural Modulus (at 23°C) | 101500 | psi | D-790 |
| Hardness | 60 | Shore D | D-2240 |
| Heat Deflection Temperature (at 264 psi) | 57 | ºC | D-648 |
| Heat Deflection Temperature (at 66 psi) | 93 | ºC | D-648 |
| Heat of Combustion | 2200 | BTU/lb | D-240 |
| Melt Flow Rate | 30 | grams/10 minutes | D-3159 |
| Melting Point | 310 | ºC | D-3159 |
| MIT Flex Life | 18000 | Cycles | D-2176 |
