PermaFelx® 55
- Chemical Family
- Polyesters
PermaFelx® 55 is a family of thermoplastic elastomers designed in a range of durometers for maximum versatility. Performance-tested, PermaFlex delivers superior results compared to rubber, TPEs and other elastomers. As opposed to cured rubber, PermaFlex can be re-ground and re-molded many times. It processes with less waste and no sulfur pollution.
Properties
- Physical Form
- Pellets
- Solid
Product families
- Thermoplastic Polyester Elastomers (TPE-E)
Other characteristics
- Brand
- PermaFelx
- End Uses
Air Ducts, Constant Velocity Joint Boots, Electrical Connectors, Footwear, Knobs, Luggage, SRS Airbag, SRS Seatbelt, Tubing
- Polymer Name
- Copolyester Elastomer (COPE)
- Processing Methods
- Injection Molding
- Markets
- Automotive & Transportation
- Consumer Goods
- Electrical & Electronics
- Healthcare & Pharma
- Industrial
- Application
PermaFlex®, and all its grades, is a thermoplastic elastomer, based on copolyester chemistry, also known as COPE or TPE-E. It eliminates the demarcation between rubbers and engineering plastics. It combines the strength and processing characteristics of engineering plastics with the performance of thermoset elastomers, a combination of the most desirable characteristics of rubbers and plastics. This combination provides benefits in processing and productivity for both molders and extruders. It also can be processed by blow molding or rotational techniques. As a thermoplastic, PermaFlex does not involve the high cost of vulcanization to obtain optimal properties. This polyester-based material offers a consistent performance over its entire operating temperature range, since its properties vary minimally from high to low temperature extremes.
- Flame Rating
- UL 94 V0
- Technology
- Elastomers
- Characteristic
- High temperature resistance
- High tensile strength
- Chemical resistant performance
- And more...
- Basic Properties
Temperature resistance; High tensile strength; Impact resistance; Wear and tear; Abrasion resistance; Resistance to weathering, oil and chemicals; High permeability resistance to fuels and oils; Flexural fatigue endurance; UV stability; Adhesion compatibility with paints, glues, plastics and metals; Creep and compression resistance; Excellent moisture vapor transmission rate; Dielectric; Good tactile and soft touch fee
- Material Features
- Abrasion Resistant
- Chemical Resistant
- Creep Resistant
- Fatigue Resistant
- Good UV Stability
- Good Weather Stability
- High Moisture Vapor Transmission
- High Temperature Resistance
- Chemical Resistance
- Acetic Acid
- Alcohols Aliphatic
- Ammonium Hydroxide Aqueous
- Diesel Oil
- Ethylene Glycol
- Hydrochloric Acid Aqueous
- Methyl Ethyl Ketone
- Motor Oil
- Chemical Inventories
- TSCA (USA)
Technical data
Table 1 of 4
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Elongation at Break (Type 1 Bar -40°C) | 900 | % | D 638 |
| Tensile Strength at Break (Type 1 Bar -40°C) | 7000 | psi | D 638 |
| Tensile Strength at Break (Type 1 Bar 73°F) | 7000 | — | — |
| Dart Impact | 320 | in/lb + | — |
| Tensile Elongation at Break (Type 1 Bar 73°F) | 900 | % | — |
Table 2 of 4
11 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity | 1.24 | g/ccm | D-792 |
| Chemical Resistance | Excellent | — | — |
| Compression | Excellent | — | — |
| Cut Resistance | Excellent | — | — |
| Density | 1.24 | g/cm3 | D 792 |
| Hydrolytic Stability | Excellent | — | — |
| Mold Shrinkage Flow Direction | 0.005 - 0.006 | in(mm) | D 955 |
| Mold Shrinkage Type 1 Bar | 0.127 - 0.152 | in(mm) | — |
| Melt Flow Rate (240°C at 2.16 kg) | 50 | g/10 minutes | D 1238 |
| Taber Abrasion Resistance(H-18, 1000 Gm, 1000 Cycles) | 30.89 | mg/revolu. | — |
| Tear Resistance(Die C) | 855 | 20 in/min | — |
Table 3 of 4
7 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Aging-Air (168 hours at 150°C) | No Change | — | — |
| Heat Aging-Brake Fluid (168 hours at 150°C) | No Change | — | — |
| Heat Aging-Transmission Fluid (168 hours at 150°C) | No Change | — | — |
| Vicat Softening Temperature (Rate A) | 400 | °F | D 648 |
| Duro Type D | 61 | — | D 2240 |
| Izod Impact Strength Notched 40°C | No Break | ft-lb/in | D 256 |
| Melt Point | 425 | °F | — |
Table 4 of 4
1 row| Characteristic | Value | Method |
|---|---|---|
| UL 94 Flame Class (Specimen 1.6mm) | HB (V-O grades available) | UL 94 |
